| Applications:
Use
For:
Commercial carpets: polypropylene (Action Bac), latex
unitary, urethane foam, unitary (Action Bac), urethane
laminate, jute, hot melt, woven, latex foam-backed
and non-backed needle-punched.
Bonds To: Concrete, underlayments, wood substrates,
terrazzo and existing resilient on all grade levels
as recommended by the carpet manufacturer.
Preparation:
- Refer
to carpet manufacturer’s specific recommendations.
- Condition
the area to be installed, adhesive and flooring
at 65°F (18°C)
or above for 48 hours before, during and 48 hours
after installation.
- Floor
must be sound, smooth, dry, clean and free of excessive
moisture or alkali. Remove dirt, wax, loose paint
and all other foreign
matter that would interfere with a good bond such
as curing agents
and sealers.
|
Application
|
Recommended
Trowel
|
Coverage
|
|
Rough-Back
Carpet
|
|
90-108 sq. ft.
|
|
Smooth-Back
Carpet
|
|
144-162 sq. ft.
|
Installation:
- Stir
any liquid on the surface into the adhesive.
- Full
spread adhesive using recommended trowel.
Note: Recommended trowel sizes are minimum
requirements. Porous
concrete and some carpet backings may require deeper
notches.
100% transfer of adhesive into the carpet backing
must be obtained.
- Install
carpet immediately into wet adhesive unless carpet
or substrate is nonporous. In this case, wait 10
– 15 minutes before installing carpet.
- Within
60 minutes, cut, fit and reposition as recommended
by the carpet manufacturer.
- Roll
floor in both directions with a 75-100 lb roller
and seal seams as
recommended by the carpet manufacturer. Stiff carpets
should be
rolled again after 2 hours. Restrict heavy traffic
over carpet for 24 hours.
- As
is customary with normal installation procedures,
do not sand, dry
sweep, dry scrape, drill, saw, beadblast, or mechanically
chip or
pulverize existing resilient flooring, backing,
lining felt, or asphalt
“cutback” adhesives or other adhesives.
These products may contain
asbestos fibers and/or crystalline silica. Avoid
creating dust. During
the installation process, adequate ventilation of
the work area should
be maintained. Persons who are sensitive to odors
and/or chemicals
should avoid the work area. Inhalation of such dust
is a cancer and
respiratory tract hazard. Smoking by individuals
exposed to asbestos
fibers greatly increases the risk of serious bodily
harm. See current
edition of the Resilient Floor Covering Institute’s
publication
“Recommended Work Practices for Removal of
Resilient Floor
Coverings” for instructions on removing all
resilient floor
covering structures.
Technical
Information:
| Technical
Data: |
HENRY
GreenLine GL62 |
| Base: |
Latex |
| Color: |
Smooth,
off-white paste |
| Taggant
Color: |
Yellow |
| Ultra
Green: |
Up
to 97% lower in emissions than CRI IAQ criteria |
| Open
Time: |
None
over porous substrates, 10 to 15 minutes over
non-porous substrates |
| Working
Time: |
60
minutes
NOTE:
Working times vary based on job conditions, substrates,
temperature and humidity |
| Size: |
4
Gallons |
| Shipping
Unit: |
Pail |
| Weight
Per Gallon: |
9.52
lbs. |
| Quantity Per Pallet: |
48
Pails |
| Shelf
Life: |
6
months if not opened |
| Storage: |
Keep
from freezing and avoid high temperatures |
Clean-up:
- Remove
wet adhesive residue with a clean, white cloth dampened
with
soapy water. Use mineral spirits for dried adhesive
residue carefully
following warnings on container.
- Do
not wet wash carpet for 5 days after installation.
- Easy
clean-up
Note: Do not reuse container.
Dispose of container and adhesive residue in accordance
with federal, state and local waste disposal regulations.
Do not flush adhesive down drains.
VOC
content:0 g/L; calculated & reported, SCAQMD 1168
UPC
Code:
0 42369 21529 9
Warranty:
HENRY
GreenLine GL62 carries The HENRY's Best 10 Year Limited
Warranty. Be assured you are using
the best product for every application by choosing
HENRY's Best!
We
warrant that GL62 will
not break down or lose
its cohesive strength
due to a manufacturing
or formulation defect
for 10 years from the
date of installation,
subject to certain exclusions
and limitations set forth
in the warranty, if used
for its stated purpose
and applied in accordance
to these instructions.
For
complete warranty details
call (800) 232-4832.
Printer
Friendly documents (pdf):
Technical Data/Installation Instructions • Formatted Specifications
MSDS: English / Spanish
|
